Beaglebone black CAN messages sending problem
0
I'm able to receive the CAN messages successfully while the CAN is in ERROR-ACTIVE state.
2: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
bitrate 500000 sample-point 0.875
tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1
c_can: tseg1 2..16 tseg2 1..8 sjw 1..4 brp 1..1024 brp-inc 1
clock 24000000
re-started bus-errors arbit-lost error-warn error-pass bus-off
7 0 0 10 16 7 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
RX: bytes packets errors dropped overrun mcast
19321178 2661559 6 0 6 0
TX: bytes packets errors dropped carrier collsns
0 0 0 11 0 0
But when I' trying to send data using cansend 280#22F18C, it shows BUS-OFF.
2: can0: <NO-CARRIER,NOARP,UP,ECHO> mtu 16 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state BUS-OFF (berr-counter tx 248 rx 0) restart-ms 0
bitrate 500000 sample-point 0.875
tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1
c_can: tseg1 2..16 tseg2 1..8 sjw 1..4 brp 1..1024 brp-inc 1
clock 24000000
re-started bus-errors arbit-lost error-warn error-pass bus-off
7 0 0 11 17 8 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
RX: bytes packets errors dropped overrun mcast
20884231 2876864 6 0 6 0
TX: bytes packets errors dropped carrier collsns
0 0 0 11 0 0
I'm receiving messages from another node using a transceiver, but unable to send the message.
linux beagleboneblack can-bus
asked Nov 14 '18 at 5:51
kqafqbcekqafqbce
11
add a comment |
0
I'm able to receive the CAN messages successfully while the CAN is in ERROR-ACTIVE state.
2: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
bitrate 500000 sample-point 0.875
tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1
c_can: tseg1 2..16 tseg2 1..8 sjw 1..4 brp 1..1024 brp-inc 1
clock 24000000
re-started bus-errors arbit-lost error-warn error-pass bus-off
7 0 0 10 16 7 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
RX: bytes packets errors dropped overrun mcast
19321178 2661559 6 0 6 0
TX: bytes packets errors dropped carrier collsns
0 0 0 11 0 0
But when I' trying to send data using cansend 280#22F18C, it shows BUS-OFF.
2: can0: <NO-CARRIER,NOARP,UP,ECHO> mtu 16 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state BUS-OFF (berr-counter tx 248 rx 0) restart-ms 0
bitrate 500000 sample-point 0.875
tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1
c_can: tseg1 2..16 tseg2 1..8 sjw 1..4 brp 1..1024 brp-inc 1
clock 24000000
re-started bus-errors arbit-lost error-warn error-pass bus-off
7 0 0 11 17 8 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
RX: bytes packets errors dropped overrun mcast
20884231 2876864 6 0 6 0
TX: bytes packets errors dropped carrier collsns
0 0 0 11 0 0
I'm receiving messages from another node using a transceiver, but unable to send the message.
linux beagleboneblack can-bus
asked Nov 14 '18 at 5:51
kqafqbcekqafqbce
11
Not sure, if you simply forgot in the question or if this could be the problem:cansend 280#22F18Cnormally should give you an error, as you need to add the interface, e.g. viacansend can0 280#22F18C.
– oh.dae.su
Nov 14 '18 at 14:19
yep typo cansend can0 280#22F12C
– kqafqbce
Nov 15 '18 at 8:49
add a comment |
0
0
0
I'm able to receive the CAN messages successfully while the CAN is in ERROR-ACTIVE state.
2: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
bitrate 500000 sample-point 0.875
tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1
c_can: tseg1 2..16 tseg2 1..8 sjw 1..4 brp 1..1024 brp-inc 1
clock 24000000
re-started bus-errors arbit-lost error-warn error-pass bus-off
7 0 0 10 16 7 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
RX: bytes packets errors dropped overrun mcast
19321178 2661559 6 0 6 0
TX: bytes packets errors dropped carrier collsns
0 0 0 11 0 0
But when I' trying to send data using cansend 280#22F18C, it shows BUS-OFF.
2: can0: <NO-CARRIER,NOARP,UP,ECHO> mtu 16 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state BUS-OFF (berr-counter tx 248 rx 0) restart-ms 0
bitrate 500000 sample-point 0.875
tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1
c_can: tseg1 2..16 tseg2 1..8 sjw 1..4 brp 1..1024 brp-inc 1
clock 24000000
re-started bus-errors arbit-lost error-warn error-pass bus-off
7 0 0 11 17 8 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
RX: bytes packets errors dropped overrun mcast
20884231 2876864 6 0 6 0
TX: bytes packets errors dropped carrier collsns
0 0 0 11 0 0
I'm receiving messages from another node using a transceiver, but unable to send the message.
linux beagleboneblack can-bus
asked Nov 14 '18 at 5:51
kqafqbcekqafqbce
11
I'm able to receive the CAN messages successfully while the CAN is in ERROR-ACTIVE state.
2: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
link/can promiscuity 0
can state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
bitrate 500000 sample-point 0.875
tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1
c_can: tseg1 2..16 tseg2 1..8 sjw 1..4 brp 1..1024 brp-inc 1
clock 24000000
re-started bus-errors arbit-lost error-warn error-pass bus-off
7 0 0 10 16 7 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
RX: bytes packets errors dropped overrun mcast
19321178 2661559 6 0 6 0
TX: bytes packets errors dropped carrier collsns
0 0 0 11 0 0
But when I' trying to send data using cansend 280#22F18C, it shows BUS-OFF.
2: can0: <NO-CARRIER,NOARP,UP,ECHO> mtu 16 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 10
link/can promiscuity 0
can state BUS-OFF (berr-counter tx 248 rx 0) restart-ms 0
bitrate 500000 sample-point 0.875
tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1
c_can: tseg1 2..16 tseg2 1..8 sjw 1..4 brp 1..1024 brp-inc 1
clock 24000000
re-started bus-errors arbit-lost error-warn error-pass bus-off
7 0 0 11 17 8 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
RX: bytes packets errors dropped overrun mcast
20884231 2876864 6 0 6 0
TX: bytes packets errors dropped carrier collsns
0 0 0 11 0 0
I'm receiving messages from another node using a transceiver, but unable to send the message.
linux beagleboneblack can-bus
linux beagleboneblack can-bus
asked Nov 14 '18 at 5:51
kqafqbcekqafqbce
11
asked Nov 14 '18 at 5:51
kqafqbcekqafqbce
11
asked Nov 14 '18 at 5:51
kqafqbcekqafqbce
11
asked Nov 14 '18 at 5:51
kqafqbcekqafqbce
11
asked Nov 14 '18 at 5:51
kqafqbcekqafqbce
11
11
Not sure, if you simply forgot in the question or if this could be the problem:cansend 280#22F18Cnormally should give you an error, as you need to add the interface, e.g. viacansend can0 280#22F18C.
– oh.dae.su
Nov 14 '18 at 14:19
yep typo cansend can0 280#22F12C
– kqafqbce
Nov 15 '18 at 8:49
add a comment |
Not sure, if you simply forgot in the question or if this could be the problem:cansend 280#22F18Cnormally should give you an error, as you need to add the interface, e.g. viacansend can0 280#22F18C.
– oh.dae.su
Nov 14 '18 at 14:19
yep typo cansend can0 280#22F12C
– kqafqbce
Nov 15 '18 at 8:49
Not sure, if you simply forgot in the question or if this could be the problem:
cansend 280#22F18C normally should give you an error, as you need to add the interface, e.g. via cansend can0 280#22F18C.– oh.dae.su
Nov 14 '18 at 14:19
Not sure, if you simply forgot in the question or if this could be the problem:
cansend 280#22F18C normally should give you an error, as you need to add the interface, e.g. via cansend can0 280#22F18C.– oh.dae.su
Nov 14 '18 at 14:19
yep typo cansend can0 280#22F12C
– kqafqbce
Nov 15 '18 at 8:49
yep typo cansend can0 280#22F12C
– kqafqbce
Nov 15 '18 at 8:49
add a comment |
0
active
oldest
votes
Your Answer
StackExchange.ifUsing("editor", function ()
StackExchange.using("externalEditor", function ()
StackExchange.using("snippets", function ()
StackExchange.snippets.init();
);
);
, "code-snippets");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "1"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: true,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: 10,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fstackoverflow.com%2fquestions%2f53293927%2fbeaglebone-black-can-messages-sending-problem%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
0
active
oldest
votes
0
active
oldest
votes
active
oldest
votes
active
oldest
votes
draft saved
draft discarded
Thanks for contributing an answer to Stack Overflow!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fstackoverflow.com%2fquestions%2f53293927%2fbeaglebone-black-can-messages-sending-problem%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Not sure, if you simply forgot in the question or if this could be the problem:
cansend 280#22F18Cnormally should give you an error, as you need to add the interface, e.g. viacansend can0 280#22F18C.– oh.dae.su
Nov 14 '18 at 14:19
yep typo cansend can0 280#22F12C
– kqafqbce
Nov 15 '18 at 8:49